UC知道我的E4600配技嘉EP35-ds3和DDR2 800 2G*2`CPU现在OC到了3.0G,希望到4.0G,如何超
来源：百度知道 编辑：UC知道 时间：2024/05/10 14:39:33
Robust Graphics Booster(绘图加速器功能) auto,fast,turbo [turbo]
cpu clock ratio(CPU倍频调整) 6,7,8. [8X]
cpu host clock control(CPU时脉控制) disabled [enabled]
cpu host frequeney(Mhz)(CPU内频调整) 100-700 [325]
pci express frequeney(Mhz)(PCI EXPRESS 区流排时脉调整) 90-150 [auto]
c.i.a.2(第2代智慧型CPU效能加速器) enabled [disabled]
performance enhance atandard,turbo,extreme(增进系统效能) [turbo]
system memory multiplier(spd)(记忆体倍频调整) auto,3.33,4.0+,2.00,2.40,3.20,2.50,3.00,4.0~ [2.40]
memory frequency(Mhz)(记忆体时脉调整) 800 600
DRAM Timing Selectable (SPD) [Manual]
CAS Latency Time 5[3]
DRAM RAS# to CAS# Delay 5 [auto]
DRAM RAS# Precharge 5[auto]
precharge delay(tRAS) 18 [auto]
ACT to ACT Delay(tRRD) 3 (auto)
RANK Write To READ Delay 3(auto)
Write To precharge Delay 52 (auto)
Read to Precharge Delay 3 (auto)
Static tRe
cpu clock ratio(CPU倍频调整) 6,7,8. [8X]
cpu host clock control(CPU时脉控制) disabled [enabled]
cpu host frequeney(Mhz)(CPU内频调整) 100-700 [325]
pci express frequeney(Mhz)(PCI EXPRESS 区流排时脉调整) 90-150 [auto]
c.i.a.2(第2代智慧型CPU效能加速器) enabled [disabled]
performance enhance atandard,turbo,extreme(增进系统效能) [turbo]
system memory multiplier(spd)(记忆体倍频调整) auto,3.33,4.0+,2.00,2.40,3.20,2.50,3.00,4.0~ [2.40]
memory frequency(Mhz)(记忆体时脉调整) 800 600
DRAM Timing Selectable (SPD) [Manual]
CAS Latency Time 5[3]
DRAM RAS# to CAS# Delay 5 [auto]
DRAM RAS# Precharge 5[auto]
precharge delay(tRAS) 18 [auto]
ACT to ACT Delay(tRRD) 3 (auto)
RANK Write To READ Delay 3(auto)
Write To precharge Delay 52 (auto)
Read to Precharge Delay 3 (auto)
Static tRe
CPU体质不同能超的幅度也不同，，倍频调小X10 X9 X8慢慢来，如果超了不能开机就说明内存不行，只能外频调12X继续超，最后一个 加电压超 电压不要超过1.39V就行了 我的CPU也是E4600 2G单条667内存 技嘉P31-S3G板子 最高抄到3.33GHZ再上去就挂了，拆开主板里的电池重新超，最后稳定在3.24GHZ
你超它干什么呢?郁闷~