In situ ultrasonic measurement of photoresist glass transition temperature
来源:百度知道 编辑:UC知道 时间:2024/05/17 02:18:28
purpose of photoresist prebake is to evaporate excess solvent from the photoresist and to allow the
polymer chains to relax into an ordered matrix. The phase of a high frequency ultrasound signal was
monitored as it was reflected from the silicon/photoresist interface during the photoresist prebake.
There was an initial decrease in phase followed by a rapid increase once a given temperature was
reached. It is believed that this repeatable temperature is the glass transition temperature of the
resist/solvent mixture and that the rapid increase in phase following it is a result of solvent
evaporation. The glass transition temperature (Tg) for a freshly spun 2.2 mm Shipley 1813 resist
was measured to be 50 °C. The Tg measured increased from 50 to 66 °C as the time delay between
coating and prebaking was increased from 0 to 20 min. It is believed t
我们研究出了一种方法来测量光刻胶玻璃的过渡温度。把光刻胶预烘干的目的是把多余的溶剂蒸发掉,并且把聚合连排列成整齐的矩阵。当光刻胶预热的时候,可以监控到从硅晶/光刻胶表面反射的高频超声波的相位。可以观测到,当到达一定的温度的时候,相位在经过了快速增长后开始减小。这个可重复实验得到的温度就是这种胶混合溶剂玻璃的过渡温度,相位的快速增长是由于溶剂的挥发造成的。2.2mm厚的新鲜希普利1813玻璃纤维的过渡温度在50度。在预热时间延迟从0增长到20分钟的时候,Tg(过渡温度)也从50度增长到66度。这种变化是由于溶液挥发造成的。
希望能帮到你。
人工翻译 有保证!!
1.a freshly spun 2.2 mm Shipley 1813 resist这个和你的专业比较接近
我不确定是什么 你自己填上好了
2. photoresist 翻译为光致抗蚀剂 或 光致抗蚀剂 译文用的是 光致抗蚀剂 楼主根据具体情况选择吧
译文:
我们研发了一种方法来衡量光致抗蚀剂的现场玻璃转化
温度。光致抗蚀剂预烘焙的目的是从光致抗蚀剂中蒸发掉
过多的溶媒而使聚合物链缓和溶入规则的基体中。在预
烘焙过程中将监测从硅/光致抗蚀剂界面反射出来的高
频超声波信号。每当达到一个给定温度时就会有一个
最初的相的减少继而出现一个快速上升。普遍认为这
种可重复的温度就是抗蚀/溶解混合剂的玻璃转化温
度,而那个紧随其后的相的快速增加之后就是溶媒的蒸发的结果。a freshly spun 2.2 mm Shipley 1813 resist
的玻璃转化温度(Tg)测定为50摄氏度。所测得
的玻璃转化温度随着镀层和预烘焙之间的时间
间隔从0分钟增加到20分钟而从50摄氏度增加到66摄
氏度。普遍认为这个玻璃转化温度的变化是溶媒蒸发
的结果。
我们已经开发了一种测试光致抗蚀剂原位玻璃转化温度的方法。光致抗蚀剂预焙的目的为蒸发光