UC知道翻译CISCO英文文档3
来源：百度知道 编辑：UC知道 时间：2024/06/06 03:38:09
These are the general cause for this error message:
Misconfiguration of the interfaces or switch ports or cabling problem.
Mismatch of primary condary IP addresses on the neighbor interface.
A switch/hub is leaking multicast packets to other ports.
If using a LAN switch, the vlans may have joined routers together.
Another router uses EIGRP advertising on the same subnet lan as this router and is misconfigured with an incorrect AS number.
In order to troubleshoot this issue, check these items:
Verify that the cable is connected correctly.
Double-check the interface configuration for misconfigured IP addresses on the local and neighboring routers.
Verify that the primary address of the interface is in the same subnet as the primary address of the neighbor router.
If the EIGRP neighbor connection is joined via a LAN hub, use separate hubs in order to break up the broadcast domain for each logical LAN segment, or configure no eigrp log-neig
Misconfiguration of the interfaces or switch ports or cabling problem.
Mismatch of primary condary IP addresses on the neighbor interface.
A switch/hub is leaking multicast packets to other ports.
If using a LAN switch, the vlans may have joined routers together.
Another router uses EIGRP advertising on the same subnet lan as this router and is misconfigured with an incorrect AS number.
In order to troubleshoot this issue, check these items:
Verify that the cable is connected correctly.
Double-check the interface configuration for misconfigured IP addresses on the local and neighboring routers.
Verify that the primary address of the interface is in the same subnet as the primary address of the neighbor router.
If the EIGRP neighbor connection is joined via a LAN hub, use separate hubs in order to break up the broadcast domain for each logical LAN segment, or configure no eigrp log-neig
看楼上的翻译我汗流不已,用的是翻译软件吧?
我来说两句
错误的主要原因如下:
交换机接口配置错误或者电缆有问题.
接口IP设置错误.
一个开关(HUB)在其他PORTS上有数据泄露.
如果有用LAN卡,可能与其他数据包混在一起.
另一个同一个局域网内使用EIGRP广告的路由器出现AS号码错误,
要解决问题,下面给一些参考意件,
确认电线连接正确.
复查路由器端口配置的IP地址.
确认所连接的路由器是主路由器.
如果EIGRP是上面所说的那样请使用单独的HUB来分割逻辑区段,或不配置LOG-NEIGHBOR-WARNING来消除警报(此处是步骤,就不翻译过来了).
如果有开关的话,请确认开关的配置,确保不同网络部分未配置为在同一个虚拟局域网共享同一广播域。
这些都是一般的原因此错误信息：
错误的接口或交换机端口或电缆的问题。
错配的主要condary IP地址的接口上的邻居。
阿交换机/集线器是漏水多播数据包到其他港口。
如果使用的是局域网交换机的VLAN可能加入路由器在一起。
另一个路由器使用EIGRP的广告在同一个子网上网络，因为这是错误的路由器和与一个不正确的数目。
为了解决此问题，检查这些项目：
确认电缆连接正确。
仔细检查接口配置错误的IP地址在本地及周边路由器。
确认的主要地址的接口是在同一个子网中的主地址的邻居路由器。
如果EIGRP邻居连接加入通过网络集线器，使用单独的枢纽，以便打破了广播域为每个逻辑网络部分，或配置不eigrp日志邻域的警告，以消除错误。
如果有一个开关参与，检查交换机的配置，以确保不同的网络部分未配置为在同一个虚拟局域网共享同一广播域。