UC知道哪位高手帮忙翻译一下？谢谢啦！！！急 ！！！
来源：百度知道 编辑：UC知道 时间：2024/06/04 09:25:57
STRAIGHT SAW
1. Clamps Out-of-Sync
The customer indicated that the rear clamp moved into the clamping position slower than the front clamp. Since the saw was not operating I was unable to observe the degree of difference in the movement of the clamps. It is worth noting that there is always a slight difference in the clamping movement. While this should not be of such a significant degree that the sawing operation starts before the clamps are in place, it is normal for the dual clamping movement.
Shunde engineers will look at the replacement or redesign of the air valves as well as provide some “fine tune” adjustments for the clamping pressure. It is possible that there is a clamping cylinder damage problem or simply a plug in the lines. Without any specific documentation on the “speed of clamping” it is hard to evaluate changes. This saw and components has not had clamping speed differential problems in the past.
However, Norwell will pr
1. Clamps Out-of-Sync
The customer indicated that the rear clamp moved into the clamping position slower than the front clamp. Since the saw was not operating I was unable to observe the degree of difference in the movement of the clamps. It is worth noting that there is always a slight difference in the clamping movement. While this should not be of such a significant degree that the sawing operation starts before the clamps are in place, it is normal for the dual clamping movement.
Shunde engineers will look at the replacement or redesign of the air valves as well as provide some “fine tune” adjustments for the clamping pressure. It is possible that there is a clamping cylinder damage problem or simply a plug in the lines. Without any specific documentation on the “speed of clamping” it is hard to evaluate changes. This saw and components has not had clamping speed differential problems in the past.
However, Norwell will pr
直缝埋弧焊1 . 夹子柱擎的客户表示后方钳搬进夹紧位置较前钳. 既然看到的是不是我的经营是无法观察的程度差异,在运动中的 线夹. 值得注意的是,总是存在着细微差别,在夹紧运动. 虽然这不应该有这么大的程度,锯开始运作之前,夹子正 地方,是正常的双重夹紧运动. 顺德工程师会看看更换或重新气阀以及提供一些"微调" 调整夹紧压力. 它可能是有一个夹紧缸损坏问题,还是只是一个插头的线路. 没有任何具体文件,对"速度夹紧"这是一个很难评估的变化. 这种锯及部件尚未夹紧速差问题,在过去的. 不过,诺韦尔将提供一个"没用"夹紧气缸作为替代,也提供了新的气门. 2 . 看到导游的导游看到的直缝埋弧焊只有大约2 "高. 这引起了支持问题时uniteca挤提4 "薄壁管. 这个尺寸薄壁管是不够方的支持,在切割操作,这起因 稍微压缩管道造成了褴褛切割水管. 锯指南将取代导游说,有4 "的高度. 此外, 我们将提供一套指南,在同一高度,只是之前的立式辊指南. 我们没有预见的是,客户将运行这种事壁管的直径. 所有这些项目将改为免费的