UC知道求助，翻译！急！
来源：百度知道 编辑：UC知道 时间：2024/06/11 10:07:54
Door benchmark - performance Introduction
Doors, hinges and check straps were purchased as spare parts
4 typical load cases were tested:
Door sag
Window frame stiffness
Over-opening
Beltline stiffness
The definition of the loadcases was done similar to many OEMs
Measurements were performed on a hydraulic test bench
Restraint:
Hinges bolted onto test bench
Lock tangentially restrained and vertically guided
Load application:
To lock position
1000 N in Z downward
Evaluation:
Displacement of load application point
Permanent deformation after load removal
Restraint:
Hinges bolted onto test bench
Lock restrained in Y and Z
Load application:
Rear/top of frame in radius
Force 350N in Y
Evaluation:
Displacement of load application points in Y
Displacement of door lower edge below lock
Restraint:
Hinges bolted onto test bench
Original check strap in ope
Doors, hinges and check straps were purchased as spare parts
4 typical load cases were tested:
Door sag
Window frame stiffness
Over-opening
Beltline stiffness
The definition of the loadcases was done similar to many OEMs
Measurements were performed on a hydraulic test bench
Restraint:
Hinges bolted onto test bench
Lock tangentially restrained and vertically guided
Load application:
To lock position
1000 N in Z downward
Evaluation:
Displacement of load application point
Permanent deformation after load removal
Restraint:
Hinges bolted onto test bench
Lock restrained in Y and Z
Load application:
Rear/top of frame in radius
Force 350N in Y
Evaluation:
Displacement of load application points in Y
Displacement of door lower edge below lock
Restraint:
Hinges bolted onto test bench
Original check strap in ope
门基准 - 性能介绍
门，绞链和检查带作为零备件被购买
4 典型的负荷箱被测试：
门下跌
窗子框架刚度
在开始上方
Beltline 刚度
loadcases的定义做类似于很多OEMs
测量数据被关于一条水压试验长凳进行
抑制：
绞链逃跑到试验长凳上
锁tangentially被阻止并且垂直引导
装应用：
对锁位置
用向下Z的1000 N
评估：
负荷应用点的替代
永久变形在装移动之后
抑制：
绞链逃跑到试验长凳上
锁用Y 和Z被阻止
装应用：
在范围里的框架的后/ 顶
在Y里强迫350 N
评估：
在Y里负荷应用点的替代
低于锁的门下边带的替代
抑制：
绞链逃跑到试验长凳上
原先的检查系牢打开位置
装应用：
对 锁位置
300 N 切线的力量
评估：
负荷应用点的替代
塑性变形
抑制：
绞链逃跑到试验长凳上
锁用Y 和Z被阻止
装应用：
连接到免费小组区域的中间
在Y里有一种200 N的力量的压缩
评估：
在Y里的负荷应用点的替代的总数
200，000 车辆/年-同一事物适合全部门的情况
门用白色的费用被确定
格林菲尔德接近
会议的向下的眼泪
部分重物被确定通过称重
得到对材料的使用的因子
确定组件
得到参考数据
知道肺结核
从现有的参考数据得到费用
形成方法和行动计划的假定
缝制的空白的生产成本部分
有身体概念和不同的用户要求的Interdependencies 必须被在评价过程中考虑
费用计算取决于被选择的边界条件。 在这里 比较。
不可能得到一一般的"乐观的门